Can I Install a Bath Tub Myself? Factors to Consider And Actions
Can I Install a Bath Tub Myself? Factors to Consider And Actions
Blog Article
We have stumbled upon this great article on Installing A Bathtub below on the net and accepted it made sense to share it with you on this page.
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult project. If the old tub is conveniently obtainable, the job can relocate easily; if you need to open a wall to remove the old tub and also place the new tub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to leave the old tub and embeded in the brand-new one. Make certain you have qualified on your own for the task as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to consider using one prior to you begin. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your bathroom if you have actually already bought a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your tools as well as material list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be fairly problematic because of the restricted gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water system as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been made use of a minimum of once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The previous kind should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that piece about Tools You Need to Install a New Bathtub while doing a search on the web. Sharing is caring. Helping others is fun. Thanks so much for taking the time to read it.
View Website
Report this page